不銹鋼風道具有減少泄露、安裝空間小、工藝精細、使用壽命長等特點和優勢。

Stainless steel air duct has the characteristics and advantages of reducing leakage, small installation space, fine process and long service life.

 減少泄漏

不銹鋼風道裝置顯著減少了管道與管道之間的連接，使管道接頭的泄漏程度降低。典型的不銹鋼管長度為3至6米，典型矩形管道的長度僅為1~1.5米;并且只需要一個管接頭來連接兩個不銹鋼管道，傳統的矩形管道連接通常需要一個完全獨立的雙法蘭系統。標準化產品。螺旋圓管道配件（管件和接頭）的生產是高度自動化，系統化和工業控制的。設備成本低。圓形管道系統的安裝時間僅為類似矩形管道的1/3。

Reduce leakage

Stainless steel air duct device significantly reduces the connection between pipes and reduces the leakage of pipe joints.Typical stainless steel pipes length 3 to 6 m, typical rectangular pipes length only 1 to 1.5 m; and only one pipe joint to connect two stainless steel pipes, conventional rectangular pipe connections usually require a completely separate dual flange system.standardized products.The production of spiral pipe fittings (fittings and joints) is highly automated, systematic and industrially controlled.The cost of equipment is low.Round piping systems are installed at only one-third of similar rectangular lines.

安裝空間小

在相同的設備空間中直徑為200毫米的圓形管可以代替250×150毫米的矩形管，而不會增加任何壓降。多個平行的圓形管道可以替代扁平的矩形管道，而無需增加額外的設備空間?？紤]到所有因素，在大多數情況下，圓形管比矩形管占用更少的空間。對于相同的壓力特性，幾個圓形管的安裝空間通常與矩形管的空間相同或更小。許多矩形管道系統需要4螺栓系統，因此在管道的所有方向上都添加了40到80mm。

The installation space is small

A circular tube of 200 mm in diameter in the same equipment space can replace a 250,150 mm rectangular tube without adding any pressure drop.Multiple parallel circular pipes can replace flat rectangular tubes without adding additional equipment space.Considering all factors, in most cases, circular tubes occupy less space than rectangular tubes.For the same pressure properties, the mounting space for several circular tubes is usually the same or less as for rectangular tubes.Many rectangular pipe systems require 4-bolt systems, so 40 to 80mm are added in all directions of the pipeline.

精細工藝

不銹鋼風道選用的進口設備模具為特殊鋼結構，即使在使用三到五年后，受限制的模具的外觀也保持不變，從而不會損壞鍍鋅鋼板的外觀，并且外觀大大延長。風管使用壽命均勻平整，咬合緊密，連接力強，密封性好。安全密封防漏系統。精致的螺旋限制羅紋工藝使得不銹鋼管道具有良好的承受壓力的強度。添加螺旋肋后，咬合的厚度是管的厚度的四倍。管道的剛度非常大，顯示出固結的優越性。它可承受最大壓力載荷而不會損壞，材料厚度可減少15％，從而降低成本。

hand work

The imported equipment mold selected for the stainless steel air duct is a special steel structure, and the appearance of the restricted mold remains unchanged even after three to five years of use, which will not damage the appearance of the galvanized steel plate, and the appearance will be greatly extended.The service life of air duct is uniform, tight occlusion, strong connection force and good sealing.Safety sealing and leakage prevention system.The delicate spiral restriction rossing process gives stainless steel pipes good pressure strength.After adding spiral ribs, the occlusion was four times the thickness of the tube.The stiffness of the pipeline is very large, showing the superiority of consolidation.It can withstand maximum pressure load without damage and reduce material thickness by 15%, thereby reducing cost.